maf00028eem MN103SE3 series type MN103SE3k mn103sfe3k internal rom type mask rom flash rom (byte) 256k ram (byte) 8k package (lead-free) qfp100-p-1818b minimum instruction execution time 16.7 ns (4.5 v to 5.5 v) ? interrupts 9 external interrupts 47 internal interrupts: watchdog timer. timer. serial i/f. pwm. a/d conversion ?nish. system error ? timer counter 8-bit timer 12 timer 0 to 7, 14 to 17 interval timer. event count. cascading connectable 16-bit timer 6 timer 8 to 10 ......... interval timer. event count. pwm output. double buffer timer 11 ................ interval timer. event count. pwm output ( 6 pins simultaneous output are available). double buffer timer 12, 13 .......... interval timer. double buffer. start synchronized with 3-phase pwm are available watchdog timer 1 ? serial interface uart (full duplex) /synchronous interfaces selective 3 serial 0, 1 ............... 7-bit, 8-bit transmission serial 2 ................... 1-bit to 8-bit transmission (synchronous). 2 and 3 channel type selectable (synchronous) ? i/o pins i/o 81 : common use 81 ? a/d converter 10-bit 3 unit. 20 channels minimum conversion time: 1.0 s simultaneous conversion of 3 series are available conversion start synchronized with 3-phase pwm or timer 12, 13 are available ? motor control pwm 16-bit 3-phase pwm 2 triangular waveform or jigsaw waveform. dead time setup. double buffer. output polar switching is available. pwm output pin protect function ? electrical charactreistics (a/d converter characteristics) parameter symbol condition limit unit min typ max non-linear error 10-bit 3 lsb a/d conversion time tad 1.0 s analog input voltage via vss vdd v ta = 25 c. vdd = 5.0 v. vss = 0 v
maf00028eem MN103SE3k, mn103sfe3k ? pin assignment qfp100-p-1818b p76, tm 11 o4 p77, tm 11 o5 p80, irq0 0 p81, irq0 1 p82, irq0 2 p83, irq0 3 p84, tm14i o tcpou t p86 p87 p90, adin00 p91, adin01 p92, adin02 p93, adin03 vs s p94, adin04 vd d p95, adin05 p96, adin06 p97, adin07 pa 0, adin08 pa 1, adin09 pa 2, adin10 pa 3, adin 11 pa 4, adin12 p16, tm17i o p15, tm16i o nrst p14, irq0 8 p13, irq0 7 p12, irq0 6 p1 1, irq0 5 p10, irq0 4 vdd2 vd d vd d vppe x vs s osci osco pb3, adin1 9 pb2, adin1 8 test 3 test 2 test 1 pb1, adin1 7 pb0, adin1 6 pa 7, adin15 pa 6, adin14 pa 5, adin13 p45, tm10bo p44, tm10ao p43, tm9bio p42, tm9aio p41, tm9bo p40, tm9ao p37, tm8bio p36, tm8aio vss p35, tm5io vdd p34, tm4io p33, tm3io p32, tm2io p31, tm1io p30, tm0io p27, sbi 0 p26, sbt0 p25, sbo 0 p24, sbi 1 p23, sbt1 p22, sbo 1 p21, sbi 2 p20, sbt2 p17, sbo 2 p46, tm10aio p47, tm10bio p50, tm6io p51, tm7io p52, pwm00 p53, npwm00 p54, pwm01 p55, npwm01 p56, pwm02 p57, npwm02 p6 0 p6 1 p62, pwm10 p63, npwm10 p64, pwm 11 p65, npwm 11 p66, pwm12 p67, npwm12 vdd p72, tm1 1io 0 vss p73, tm1 1io 1 vdd 2 p74, tm1 1o 2 p75, tm1 1o 3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
request for your special attention and precautions in using the technical information and semiconductors described in this book (1) if any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and regulations of the exporting country, especially, those with regard to security export control, must be observed. (2) the technical information described in this book is intended only to show the main characteristics and application circuit examples of the products. no license is granted in and to any intellectual property right or other right owned by panasonic corporation or any other company. therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other company which may arise as a result of the use of technical information described in this book. (3) the products described in this book are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). consult our sales staff in advance for information on the following applications: ? special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the prod- ucts may directly jeopardize life or harm the human body. ? any applications other than the standard applications intended. (4) the products and product specifications described in this book are subject to change without notice for modification and/or im- provement. at the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date product standards in advance to make sure that the latest specifications satisfy your requirements. (5) when designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions (operating power supply voltage and operating environment etc.). especially, please be careful not to exceed the range of absolute maximum rating on the transient state, such as power-on, power-off and mode-switching. otherwise, we will not be liable for any defect which may arise later in your equipment. even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (6) comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (esd, eos, thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. when using products for which damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages. (7) this book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of our company. 20080805
|
